Getting Started with Plumbing Basics When Installing a Bathtub
Getting Started with Plumbing Basics When Installing a Bathtub
Blog Article
Were you trying to locate additional info about A Step-by-Step Guide to Installing a Bathtub?
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a brand-new one is additionally a reasonably challenging project. If the old bathtub is conveniently accessible, the task can relocate speedily; if you need to open up a wall to get rid of the old tub as well as place the brand-new tub, the task is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will certainly need a helper to move out the old bathtub and also embeded in the brand-new one. Ensure you have actually qualified on your own for the job and also are comfortable trying it. As opposed to hiring a service provider to take over a halfway-completed task, it is far better to consider using one prior to you begin. Possibilities are you might need a specialist plumber to make tube connections.
This short article will certainly assist you set up a new bathtub in your washroom if you have already gotten a new tub and also do not need to alter the plan of your previous water system pipelines.
Your devices as well as material checklist ought to comprise the following:
Planning for the Installation
Firstly, the supporting framework supplied with the bath ought to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the tap features a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets unit to prevent strain on the bath tub.
Fit the versatile faucet ports to the bottom of both faucets using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you use all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must currently prepare to be fitted in its final setting.
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, after that the first thing you need to do is separate the water. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome as a result of the limited gain access to that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipelines have been removed, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Before moving on to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Using the two wooden boards under its feet, place the bath tub in the called for position. The wood boards are handy in evenly spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by checking the spirit level and also changing the feet on the bathtub till the spirit level checks out level.
To mount taps, fit all-time low of the outermost adaptable tap port to the proper supply pipeline by making a compression join; after that do the very same for the various other tap.
Turn on the water system and also check all joints and also new pipework for leakages and also tighten them if necessary. Fill up the bathtub as well as also check the overflow electrical outlet and also the typical electrical outlet for leakages.
Ultimately, repair the bath paneling as explained in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has been utilized a minimum of once as this will settle it right into its final setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic port to stop damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin guaranteeing that the washing machines are in location between the faucet and the sink. Safeguard the faucet in place with the maker given backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous kind should be linked to the tap ends initially, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to break a rigid seal, causing the water to permeate the wall surface between the bath and also the tiling, leading to difficulties with wetness and possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures as well as installations. They are marketed in tubes as well as cartridges, and also are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked newspaper or soft rope. Remember to constantly fill up the tub with water prior to securing, to permit the movement experienced when the bathtub is in use. The sealant can crack rather early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently offered on the marketplace. It is suggested to fit the floor tiles using waterproof or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that review about Installing A Bathtub when doing a search on the internet. Are you aware of somebody who is fascinated by the subject? Feel free to promote it. Thank-you for your time invested reading it.
This Site Report this page